1.General Introduction
Honeywell FS7 Flame Detector provides intelligent two-stage response to semiconductor wet bench fires as an ALERT and FIRE ALARM, Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish. Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.
The FS7-2173 is used with the FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.
The FS7-2173-2RP unitized model’s microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor’s built-in self-test and verifies proper operation. FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a FS7 Interface Kit and the Windows-based PC software.
2.General Specifications
|
Items
|
Description
|
|
Field of view
|
120° horizontal and vertical
|
|
Response time
|
Alert: 4” dia. Polypropylene pool fire (3kW) within 5 seconds
Alarm: 8” dia. dia. Polypropylene pool fire (13kW) within 5 seconds
|
|
Spectral sensitivity
|
Visible: 400 – 900 nanometers
Near Band IR: 0.7 – 1.1 microns
Wide Band IR: 0.7 – 3.5 microns
|
|
Operating voltage
|
24 VDC nominal (18-28 VDC) - Regulated
|
|
Power consumption
|
Operating: 55mA @ 24 VDC nominal
Alarm: 80mA @ 24 VDC nominal
|
|
Output relays
|
Alert: SPST, N.O., De-Energized
Fire Alarm: SPDT (NO / NC) – De-Energized/Energized, Latching/Non-Latching
Fault: SPST (NO) – Normally Energized, Latching/Non-Latching
Contacts rating: 1 amp @ 24 VDC
|
|
Communication
|
RS-485, FireBus II
|
|
Visual Indication
|
Red LED
|
|
Temperature Range
|
32º to +158ºF (0º to +70ºC)
|
|
Humidity Range
|
10% to 90% relative humidity, non-condensing
|
|
Enclosure Materials
|
Dust tight, watertight, heat sealed, injection-molded polypropylene
|
|
Enclosure Type
|
IP67
|
|
Certifications
|
FM 3260, FM 3600, FM 3611 CSFM Listed (California State Fire Marshall)
|
|
Mounting
|
Chassis mount slide bracket
|
|
Warranty
|
Two years from date of shipping
|
3.Order Code Selection
|
Part No.
|
Description
|
|
FS7 - Detectors Part
|
|
FS7-2173
|
Viton O-ring. For use with FS7-130-SX Controller
|
|
FS7-2173-2RP
|
Non-Latching Alert and Alarm relays. Viton O-ring.
|
|
FS7-2173-2RP-K
|
Non-Latching Alert and Alarm relays. Kal-rez O-ring.
|
|
FS7-2173-KALO
|
Kal-rez O-ring. For use with FS7-130-SX Controller
|
|
Controller Systems FS7
|
|
FS7-130-SX
|
Multi-Zone Compact Controller, designed to be installed in Fire Panels, which monitors up to 12 Model FS7-2173 Fire Detectors. Programmable for up to 4 zones with relay outputs for ALERT and ALARM. Requires 24 VDC. Approvals: FM & CSFM
|
|
FS7 - Accessories Part
|
|
FS-746-B
|
Test Lamp. Battery operated for testing FS7 Fire Detectors up to 10 ft. distance.
|
|
FT-S7
|
Test Lamp. Battery operated for testing FS7 Fire Detectors up to 2 ft. distance.
|
|
FS7-2179
|
Junction Box for connecting Model FS7-2173 Fire Detectors in a daisy chain or star configuration. Complete with (4) Lemo female connectors. Required for Model FS7-130-SX applications.
|
|
FS7 - Interconnection Cables
|
|
CBMM-5
|
5 ft. cable with Male/Male Lemo connectors, (Junction Box to Junction Box).
|
|
CBMM-10
|
10 ft. cable with Male/Male Lemo connectors, (Junction Box to Junction Box).
|
|
CBMO-20
|
20 ft. cable with Male Lemo connector/open pigtail, (Junction Box to Model FS7-130-SX Controller or Model S7-2175 Control Panel)
|
|
CBMO-50
|
50 ft. cable with Male Lemo connector/open pigtail, (Junction Box to Model FS7-130-SX Controller or Model S7-2175 Control Panel).
|
|
Spare Parts
|
|
PSU-12
|
110/220 VAC, 50-60 HZ Input /15 VDC Output : Universal Charger for Interface Box or DD Series, FT Series and TL Series Test Lamps
|
|
PW-3123-0002
|
Replacement Battery for FT-S7 Tester (1 required)
|